ซอย สะแกงาม14
ซอย บางกระดิ่16

เครื่องปิกปากกล่องด้วยเทปกาว (รหัส: FXJ6050)

คะแนน:

            

FXJ6050

SEMI-AUTOMATIC CASE-SEALING MACHINE

 

OPERATION INSTRUCTION

I. TECHNOLOGY PARAMETERS

Model

Unit

FXJ6050

FXJ6050A

Max size of case(W×H)

mm

500×600

Min size of case(W×H)

mm

150×900

Sealing capacity

 

1000pcs(standard size)

Height of desktop

mm

640800

Adhesive tape

 

BOPP, water-proof tape, PVC tape

Width of tape

mm

36,48,60

Way of transmission

 

Bottom-surface transmission mechanism

Width of conveyor belt

mm

50

Overall size(L×W×H)

 

1665×740×(13601650)

Power

 

Single phase 220V, 50HZ, 180W

Motor

 

Dual motor

Weight

kg

120

Printing rows

rows

 

13

Height range of printing-words

mm

 

100260

Standard word size

(W×H)

mm

 

6×12

 

II. FUNCTIONS AND FEATURES

This case-sealing machine is mainly suitable for sealing and packing of cartons, which can be used independently or as a necessary apparatus to a production line. It is widely used in the fields of domestic electrical appliances, textiles, foodstuffs, general merchandise, medicine, chemical products, etc. It adopts adhesive tape to seal cartons, which is fast and economical, easy to operate and simple to maintain; adjust the size of cartons discretionarily, simple and easy; finish upper and lower sealing at one time; ink printing equipment attached (FXJ6050A), which can be used to print manufacture date, lot number or necessary words legend on the side-face of cartons after sealing; adopting printing adhesive tape further promotes the image of products.

 

.LEGEND OF FXJ6050

 

1).HEIGHT ADJUSTMENT CRANK HANDLE     2).HEIGHT RULE GAUGE

3).TAPE PEDESTAL                            4).TAPE HEAD

5).MOTOR                                    6).CONVEYOR BELT GUARDS

7).UPPER TAPE HEAD MECHANISM            8).LOCKING KNOB

9).CONVEYOR ROLLER                       10).LOCKING KNOB

11).COVER- PRESSING STICK                  12).CARTON LOCATING WHEEL

13).CONVEYOR TABLE                        14).POWER SWITCH

15).FRAME FOUNDATION                     16).LEVELING ADJUSTER

17).CASTER                                   18). COVER-PRESSING STICK 4

 

.OPERATION PROCEDURES:

1.Place this machine on horizontal ground, lock the casters (17), adjust the legs (16) to suitable height and make the frame foundation (15) into horizontal position.

2.Place the cartons on the roller conveyor table (13):

A. Adjust height adjustment crank handle (1) in order to make the conveyor baseplane of the upper tape head mechanism (7) about 3 to 5 mm lower than the height of cartons.

B. Unlock the locking knob(10), adjust the conveyor roller (9) to lean close with the carton, and then lock the locking knob.

C. Adjust carton locating wheel (12) and conveyor roller as well, in order to lean close with the carton and then lock the locking knob(8).

3.Turn on the power switch (14) to start work, then push the carton to seal. If the tightness of upper and lower tape is not in accordance with each other, just adjust the knob to the tape pedestal (3). (Generally speaking, if the tape is too tight, just loosen the spring stress; if the condition is the opposite, use the opposite method.)

4.If the length of tape’s two terminal is not the same, then adjust the knife in the tape head (4). (Generally speaking, if the tape is long head and short tail, you only need to adjust the knife, loosen the locking screw, and pull the knife a little outer, then lock the screw; if the condition is the opposite, use the opposite method.)

 

V.INSTALLATION OF CONVEYOR TABLE & PRESSING-COVER STICK

 

1).FIXED BOARD                     2).LOCKING NUT

3).LOCKING SCREW                  4). COVER- PRESSING STICK

5). COVER-STICK                     6).CONVEYOR TABLE

7).CONNECTING SCREW

 

1. Telescope the conveyor table (13) into the connecting screw, which is in the frame foundation (15) and press down tightly.

2.Telescope the cover- pressing stick into two holes in the fixed board, which is on the upper tape head mechanism, then revolve the locking nut into the locking screw, go through cover- pressing stick, which should be pressed tightly by locking screw and be fixed on the fixed board by locking nut.

 

 

 

VI.TOOL LIST ATTACHED TO THE MACHINE

NO.

NAME

QUANTITY

UNIT

1

M5, M6, M8 hexagon ring spanner

One for each

pcs

2

3A fuse

2

pcs

3

Cross-point, and common screw driver

One for each

pcs

4

fixed-wrench 8-10, 14-17, 19-22

One for each

pcs

5

brush

1

pcs

 

 

ความเห็น
Copyright MAXXmarketing GmbH
JoomShopping Download & Support